Subscribe to TMBRMAN TV on YouTube
Many people may not be aware of the various techniques and hacks that can be used to make woodworking projects easier and more efficient. From using a magnet on a framing hammer to prevent dropped nails, to making consistent cuts with marked miter saws and tables, there are many tips and tricks that can be utilized. Additionally, techniques such as wood bending, ply cutting, and preventing wood split can help create professional-looking projects with ease.
One important hack to note is how to find the center of any width, which can be achieved by angling a tape to a number easily divisible by two. By marking the tape at specific intervals, a perfect circle can be created using a nail or screw, string, and pencil. These techniques and more will be explored in this article, providing readers with valuable information to improve their woodworking skills.
Key Takeaways
- Utilize a magnet on a framing hammer to prevent dropped nails and make hard-to-reach places easier to work with.
- Make consistent cuts by marking miter saws and tables and utilizing notches in a speed square.
- Use techniques such as wood bending, ply cutting, and preventing wood split to achieve professional-looking projects with ease.
Subscribe to 731 Woodworks on Youtube
Framing Hammer Magnet
One of the most useful tools in a carpenter’s toolbox is the framing hammer magnet. It has a magnet on the top of the hammer that allows the carpenter to place a nail on it and not worry about it falling off. This is especially useful when driving nails into hard-to-reach places.
Straight Cut Technique
To achieve a straight cut, one can use a speed square to guide the saw. Place the speed square on the mark and let the saw’s fence run across it. For hard-to-reach places, there’s a magnet on the top of the framing hammer that can hold a nail in place.
Wood Bending
To bend a straight piece of wood around a radius, a series of cuts can be made not all the way through across the back. The blade depth should be set to where it’s not all the way through the board. If cutting through ply without any tape on it, it will likely split. However, putting a couple of pieces of tape before cutting can prevent splitting.
Ply Cutting
Cutting plywood can be a tricky task, but with the right techniques, it can be done with ease. To start, it is important to set the blade depth of your saw to where it is not all the way through the board. This will prevent any splintering or damage to the plywood. If you are cutting through ply without any tape on it, there is a high chance of splintering. To prevent this, it is recommended to put a couple of pieces of tape on the plywood before making the cut.
Consistent Cuts
Making consistent cuts is essential when working on any woodworking project. Whether you’re a beginner or an experienced woodworker, achieving consistent cuts can be challenging. However, there are some hacks that can help you make consistent cuts every time.
One of the easiest ways to make consistent cuts is by marking your saw or miter saw. This will help you make the same cuts every time and avoid mistakes. Additionally, you can use a speed square to ensure that your cuts are straight. Simply place the speed square on your mark and let the fence of your saw run across it.
Square Notches
If you need to make a three-inch mark on your wood, you can use the notches on your square. Simply slide the square down the wood until you reach the three-inch mark, and there it is.
Preventing Wood Split
When screwing on the edge of a piece of wood, it is common for it to split out. To prevent this, one can tap the end of the screw with a hammer. This will prevent it from splitting.
Another way to prevent wood split is by making a series of cuts not all the way through across the back of the wood. Set the blade depth to where it’s not all the way through the board. This technique can be used when trying to take a straight piece of wood and make it bend around a radius.
Burned Wood Look
One fun way to achieve a burned wood look is by using a torch. After burning the wood, apply a wood oil product to make the burnt areas stand out.
Finding Center of Width
To find the center of any width, angle the tape to a number easily divisible by two, such as eight inches. Mark four inches, then mark three and a quarter inches on either side of the four-inch mark. This will give you the center point of the width.
Making Perfect Circle
To make a perfect circle, there are a few methods one can use. The first method is to drive a nail or screw at the center point of the circle. Then, take a string and loop it around the nail. After that, take a pencil and make a few loops around it. This will create a guide for the circle.
Another method is to use a tape measure. Lock the tape at the desired measurement for the circle’s radius. Then, set it in place and take a pencil to go around it, following the guide of the tape measure.
Cutting Circle
To cut the circle, a jigsaw can be used by coming at an angle and then cutting around. To mark the center of a piece of wood, a jig can be made out of three screws, a little piece of wood, blue tape, and a square.
To hang a battery or any picture, one can take some blue tape, lay it across the top, and poke the holes out. Then, they can line it up and drive two screws right where they punch those holes.
If someone wants to make a 45, they can take their square again and hold it up against their cut. These are just a few hacks to make woodworking easier.
Marking Center
When working on woodworking projects, it is important to mark the center of the wood accurately. This can be achieved through various methods, as demonstrated in the video.
One method is to angle the tape to a number easily divisible by two, such as eight inches, and mark four three and a quarter points. This will give an accurate center point to work with.
Another method involves driving a nail or screw at the center point and looping a string around it. The string can then be looped around a pencil to create a circle or used as a guide for other markings.
For more precise marking, a jig can be created using three screws, a piece of wood, and blue tape. The jig is placed on the wood and twisted to score the center point.
Once the center point is marked, it can be used for various purposes such as making perfect circles or hanging pictures. Blue tape can be used to poke holes for hanging and prevent damage to the wood surface.
By utilizing these marking techniques, woodworking projects can be completed with greater accuracy and precision.
Hiding Screws
When working with wood, it is important to know how to hide screws to achieve a clean and professional look. Here are some tips and tricks to hide screws effectively:
- Chisel Back the Top: Before hiding a screw, chisel back the top of the wood to create a small pocket for the screw head to sit in. This will allow the screw to be flush with the surface of the wood.
- Apply Glue: Apply a small amount of glue to the hole where the screw will be placed. This will help secure the screw in place and prevent it from loosening over time.
- Clamp the Wood: Once the screw is in place, clamp the wood together tightly until the glue dries. This will ensure that the screw stays in place and the wood remains flush.
- Sand the Surface: After the glue has dried, use a sander to clean up the surface of the wood. This will help to hide any imperfections and create a smooth finish.
By following these simple steps, you can easily hide screws and achieve a professional look in your woodworking projects. Remember to always take your time and work carefully to ensure the best results.
Hanging Pictures
When it comes to hanging pictures, there are a few tricks that can make the process easier and more efficient. One of the first tips is to use the magnet on the top of a framing hammer to hold a nail in place, making it easier to drive the nail into hard-to-reach places.
Making 45 Degree Cut
To make a 45-degree cut hold the square up against the cut and adjust it as necessary. Once the square is in place, run the fence of the saw across it to make the cut. This will ensure that the cut is straight and at the desired angle.
It is important to note that the square should be placed on the mark before making the cut. This will ensure that the cut is made in the correct location.
Using a square is a simple and effective way to make a 45-degree cut. With a little practice, anyone can make precise cuts with ease.